您的当前位置:首页>新闻资讯 > 公司动态 >

修复翻新后的车灯,如何做到质保3年?

来源:http://www.sdrunao.com/ 发布时间:2020-04-28   发布人:admin
  汽车大灯灯罩用久了难免会老化泛黄、刮擦,这不仅不美观而且还会影响大灯的透光性。现在要让这些大灯恢复如新,大家看好了。
  It is inevitable that the headlamp shade will be aged, yellowed and scratched after being used for a long time, which will not only affect the aesthetics but also the light transmittance of the headlamp. Provincial auto repair - now we need to make these headlights as new as before. Everyone is optimistic.
  1清洗大灯表面,检查车灯损坏部位并确认大灯是否可以修复
  1 clean the headlamp surface, check the damaged parts of the headlamp and confirm whether the headlamp can be repaired
  注意了,大灯内部出现的裂痕或者破碎现象是不能完全修复的!
  Note that the cracks or breakage in the headlight cannot be completely repaired!
  2依次180#240#320#干磨砂纸打磨车灯受损、老旧部位
  2 180 × 240 × 320 × dry sandpaper shall be used to polish the damaged and old parts of the lamp
  打磨使用砂纸视大灯损坏程度而定,损坏部位伤痕必须完全打磨平整
  Sandpaper shall be used for grinding depending on the damage degree of headlight. The damaged parts and scars must be completely polished
  3400#干磨砂纸打磨车灯全部表面
  3400 × dry abrasive paper to polish all surfaces of the lamp
  注意打磨时大灯受损部位粗砂纸砂印必须全部处理干净,大灯原本表面镀膜需全部磨尽
  Pay attention to the rough sandpaper sand marks on the damaged parts of the headlight must be completely cleaned, and the original surface coating of the headlight must be completely ground
  4依次使用400#600#800#1000#2000#干磨砂纸打磨车灯表面
  4. Polish the lamp surface with 400 × 600 × 800 × 1000 × 2000 × dry abrasive paper in sequence
  打磨大灯表面时注意砂纸顺序每层砂纸印必须磨尽
  When grinding the headlamp surface, pay attention to the sandpaper sequence. Each sandpaper print must be worn out
  52000#水磨砂纸打磨车灯表面清洗车灯并除水
  52000 × water abrasive paper is used to polish the lamp surface, clean the lamp and remove water
  打磨时注意残留粗砂砂印
  Pay attention to residual coarse sand mark during grinding
  6使用遮蔽膜遮蔽大灯内侧不需喷涂部位
  6. Use the mask to cover the inside of the headlamp without spraying
  遮蔽时注意大灯边角
  Pay attention to the corner of headlight when sheltering
  7除尘并喷涂钜轩车灯修复镀膜液
  7. Dedusting and spraying juxuan lamp repair coating liquid
  大灯镀膜液使用前需摇晃均匀,喷涂镀膜液时注意镀膜液喷涂厚度并喷涂光亮无脏点灰尘颗粒
  The headlamp coating solution shall be shaken evenly before use. When spraying the coating solution, pay attention to the thickness of the coating solution and spray it bright without dirty dust particles
济南宝马专修
  8专用光谱仪固化大灯表面镀膜液
  8. Special spectrometer solidifies the coating liquid on the headlamp surface
  使用光谱仪时必需佩戴专用防护面罩并提醒观看人员切勿直视光谱仪灯光
  When using the spectrometer, it is necessary to wear a special protective mask and remind the viewer not to look directly at the light of the spectrometer
  9撕去遮蔽膜并检查大灯表面修复效果
  9 remove the mask and check the repair effect of headlamp surface
  大灯表面如有灰尘颗粒需用2000#水磨砂纸打磨并抛光
  If there are dust particles on the headlamp surface, it shall be polished with 2000 × water abrasive paper
  10清洗大灯除去残留水份完成修复
  10. Clean the headlight to remove the residual water and complete the repair
  大灯修复与翻新的效果很明显吧?!现在大家来看看几组对比图,特别是第3组,效果特别特别好!
  The effect of headlight repair and renovation is very obvious, right?! Now let's take a look at a few groups of comparative pictures, especially the third group, which has a very good effect!
上一篇:新手开车 五大“莫名其妙”故障要注意! 下一篇:什么样的停车位是合法车位?

相关推荐 RELATED RECOMMENDATIONS